Comenzi uzuale pentru Huawei GPON OLT
Luam ca exemplu din HUAWEI GPON OLT, frame 0, cardul 2, port 1 si ONT 14
– Ca sa aflam ce service port este alocat (mai exact 287):
MA5680T#display service-port port 0/2/1 ont 14 { <cr>|gemport<K>|sort-by<K> }:
Command:
display service-port port 0/2/1 ont 14
Switch-Oriented Flow List
—————————————————————————-
INDEX VLAN VLAN PORT F/ S/ P VPI VCI FLOW FLOW RX TX STATE
ID ATTR TYPE TYPE PARA
—————————————————————————-
287 618 common gpon 0/2 /1 14 55 vlan 3 – – up
—————————————————————————-
Total : 1 (Up/Down : 1/0)
– Ca sa aflam ce mac-uri sunt în spate:
MA5680T#display mac-address service-port 287
———————————————————————-
SRV-P BUNDLE TYPE MAC MAC TYPE F /S /P VPI VCI VLAN ID
INDEX INDEX
———————————————————————-
287 – gpon f4ec-38a8-8ef5 dynamic 0 /2 /1 14 55 618
287 – gpon 0022-b004-7cd4 dynamic 0 /2 /1 14 55 618
———————————————————————-
Total: 2
Note: F–Frame, S–Slot, P–Port, F/S/P indicates PW Index for PW,
A–The MAC address is learned or configured on the aggregation port,
VPI indicates ONT ID for PON, VCI indicates GEM index for GPON,
v/e–vlan/encap, pri-tag–priority-tagged,
ppp–pppoe, ip–ipoe, ip4–ipv4oe, ip6–ipv6oe
-deci avem 2 terminale/pc-uri in spatele ONT-ului: f4:ec:38:a8:8e:f5 si 00:22:b0:04:7c:d4
– Pentru a da un restart la ONT:
MA5680T#interface gpon 0/2 MA5680T(config-if-gpon-0/2)#ont reset 1 14 Resetting the ONT(s) will interrupt all services on the ONT(s) Are you sure to reset the ONT(s)? (y/n)[n]: y
MA5680T(config-if-gpon-0/2)#
! FAULT WARNING 2025-15-68 08:06:20+02:00
ALARM NAME :The distribute fiber is broken or the OLT cannot receive
expected optical signals from the ONT(LOSi/LOBi)
PARAMETERS :FrameID: 0, SlotID: 2, PortID: 1, ONT ID: 14, Equipment ID:
245HMA5680T(config-if-gpon-0/2)#
! RECOVERY CLEARED 2025-15-68 08:06:58+02:00
ALARM NAME :OLT can receive expected optical signals from ONT(LOSi/LOBi
recovers)
PARAMETERS :FrameID: 0, SlotID: 2, PortID: 1, ONT ID: 14, Equipment ID:
245H
– Ca sa vedem în timp real traficul de pe porturi (în acest exemplu am luat numai portul 4):
MA5680T(config)#interface gpon 0/2
MA5680T(config-if-gpon-0/2)#display ont traffic 1 14 4
MA5680T(config-if-gpon-0/2)#
—————————————————————-
Traffic Information
—————————————————————-
Up traffic (kbps) : 0
Down traffic (kbps) : 56
—————————————————————-
– Ca sa vedem cum sunt porturile:
MA5680T(config)#interface gpon 0/2
MA5680T(config-if-gpon-0/2)#display ont port state 1 14 eth-port all
—————————————————————————–
ONT-ID ONT port-ID ONT Port-type Speed(Mbps) Duplex LinkState
—————————————————————————–
14 1 GE – – down
14 2 GE – – down
14 3 GE – – down
14 4 GE – – down
—————————————————————————–
– Ca sa dam reset factory (sa zicem ca a reusit cel de la cap sa seteze in asa fel incat nu mai poate intra pe ONT cu management):
MA5680T(config)#interface gpon 0/2 MA5680T(config-if-gpon-0/2)#ont factory-setting-restore 1 14
– Ca sa vedem ce ip este configurat pe ONT:
MA5680T(config-if-gpon-0/2)#display ont ipconfig 1 14
——————————————————————–
ONT IP host index : 0
ONT config type : Configuration file
ONT IP : 10.23.23.23
ONT subnet mask : 255.0.0.0
ONT gateway : –
ONT primary DNS : –
ONT slave DNS : –
ONT MAC : 0000-1111-2222
ONT manage VLAN : –
ONT manage priority : –
Dscp mapping table index : –
——————————————————————–
– Pentru adaugare ip pe ONT fara management:
MA5680T(config-if-gpon-0/1)#ont ipconfig 1 14 static ip-address 192.168.23.2 mask 255.255.255.0 gateway 192.168.23.1 vlan 3
{ <cr>|pri-dns<K>|priority<K>|slave-dns<K> }:
Command:
ont ipconfig 1 14 static ip-address 192.168.23.2 mask 255.255.255.0 gateway 192.168.23.1 vlan 3
Stiri pe scurt HUAWEI:
No feed items found.
Salut..
Ma intereseaza sa implementez o soluti gpon in reteaua mea. Imi poti oferi ajutor te rog… Vreau sa stiu ce echipament OLT recomanze si echipamente ONT.
Multumesc
Nu stiu ce ajutor sa-ti dau, noi le-am descoperit pas cu pas. Poate sa-ti zic de unde am luat echipamentele si sa-ti dau legatura cu chinezii de unde le-am luat.